Showing results: 1021 - 1035 of 1675 items found.
-
2732 IN -
Standard Electric Works Co., Ltd
● High quality Taut Band movement.● Three insulation test voltages(DC) : 250V, 500V, 1000V.● Two continuity test on "low ohms" : 3Ω & 500Ω.● Compact and lightweight.● AC voltmeter with linear scale up to 600 Vac.● 200mA continuity short circuit current.● 1mA test current on insulation test at nominal voltage.● Automatic discharge of capacitive and inductive circuit with charge stored in the circuit under test.● Live warning and display or external voltage presence.● Fuse, air gap, crowbar and overload protected.● On line battery monitoring shows if battery is ok.● Manual zero ohm adjustment.● Low battery consumption.● Mirror scale.● Push and turn locking switch for continuous and hand free testing.● Designed for meet international standards.● Supplied with high quality test leads.● BS 16 edition.
-
4132 IN -
Standard Electric Works Co., Ltd
● High quality Taut Band movement.● Three insulation test voltages(DC) : 250V, 500V, 1000V.● Two continuity test on "low ohms" : 3Ω & 500Ω.● Compact and lightweight.● AC voltmeter with linear scale up to 600 Vac.● 200mA continuity short circuit current.● 1mA test current on insulation test at nominal voltage.● Automatic discharge of capacitive and inductive circuit with charge stored in the circuit under test.● Live warning and display or external voltage presence.● Fuse, air gap, crowbar and overload protected.● On line battery monitoring shows if battery is ok.● Manual zero ohm adjustment.● Low battery consumption.● Mirror scale.● Push and turn locking switch for continuous and hand free testing.● Designed for meet international standards.● Supplied with high quality test leads.● BS 16 edition.
-
KHZ43201 -
Beijing KeHuan Century EMC Technology Co,.LTD
The KHZ43201 voltage probe is a standard low resistance test probe, which meets the technical requirements for this product in the CISPR16-1 and CISPR14-1 test equipment. When measuring the interference voltage of the power grid, the artificial power supply network cannot be used at the load port, and sometimes it is necessary to use a voltage probe to measure the interference of the signal port, the load port, and the antenna port. The input impedance of the voltage probe to the ground wire is greater than 1.5KΩ, which can protect the input terminal of the receiver.
-
PFM61000-8A -
Lisun Electronics Inc.
PFM61000-8A Magnetic Field Generator is high reliability test equipment with stable performance, specially designed for electrical and electronic products for measuring immunity characteristics and requirements of normal frequency magnetic fields. It provides an accurate basis for the tested equipment in the immunity test of normal frequency magnetic field. The generator can imitate the magnetic field environments such as residential, commercial, industrial and mining enterprises, power plants, as well as middle and high substation. It fully meets IEC61000-4-8 and GB / T17626.8 standards.
-
Neutronics Manufacturing Co.
NMC''s Transformer BDV Oil Test Set is a portable unit as per relevant Indian Standard Specification IS :6792 :1992, suitable for operation on 230 / 240 Volts, A.C. 50 Hz. A three core flexible cable is connected to the unit with three pin socket to connect the mains. The H.V. Transformer is a completely dry, resin encapsulated with two H.V. terminals with mounting saddles. The center point of the transformer is earthed, so that the voltage of each terminal to earth is only half the test voltage.
-
PCI EmbeddedComputer Systems
Measurement and testing of CompactPCI® assemblies in the 3U Euro-board form factor is greatly facilitated by the use of this test adapter. Easy access to the DUT is guaranteed because the adapter has plug-in connections on 3 sides. The Modern BRIDGE design permits up to 3 CompactPCI® cards and one standard PCI® card to be inserted in one CompactPCI® slot. This allows system developers to implement a large number of tests with little effort and enables you to achieve vital time to market.
-
PCI EmbeddedComputer Systems
Measurement and testing of CompactPCI® assemblies in the 6U Euro-board form factor is greatly facilitated by the use of this test adapter. Easy access to the DUT is guaranteed because the adapter has plug-in connections on 3 sides. The Modern BRIDGE design permits up to 3 CompactPCI® cards and one standard PCI® card to be inserted in one CompactPCI® slot. This allows system developers to implement a large number of tests with little effort and enables you to achieve vital time to market.
-
Insight -
HORIBA, Ltd.
Today’s environment confronts lab managers in new, challenging ways. The current regulations demand increasingly complex test procedures that require more time and resources to execute, which counteracts the goals to improve productivity and reduce costs. Therefore, lab managers need to maximize the test cell availability by continual awareness of the current situation in their facility. They must ensure the equipment is fully functional, meets all mandatory quality standards and regulations, and is up to date with all service and maintenance requirements.
-
TWA Standard Series -
Amperis sl
The TWA standard series instruments are designed to measure the resistance of six coils and simultaneously analyze the three-phase tap changer on load of the primary and secondary transformer coils (provided by model TWA40). This is done in a single cable configuration, with test currents up to 40A. Each transformer configuration has a special measurement algorithm that is optimized for rapid stabilization of test results. The TWA instruments generate a true DC current without ripple. Both current injection and magnetic circuit energy discharge are automatically regulated.
-
MSP Corporation
All filter test equipment from TSI, used for testing efficiencies of filter media and a variety of air filters, including high and very high-efficiency filters, respiratory filters, cartridges, and protective garments, is known for its simple and reliable operation. All of our filter testers can determine the efficiency of filters using submicron poly- and monodisperse oil and/or sodium chloride aerosol. Additionally, TSI's filter test solutions are used to comply with various testing standards and regulations around the globe.
-
TAND220A -
Amperis sl
The measuring instrument type TAND220A complies with the international standard IEC 61620. The instrument is based on the so-called "low-amplitude, low-frequency alternating current square wave method" and allows accurate measurements of conductivity and relative permittivity. Conductivity measurement in the range of 0.01 pS/m to 20,000 pS/m allows the use of this instrument for quality control of high resistivity liquids even at room temperature. The TAND220A works with a low test voltage and also with a low test current so that it does not represent a danger for the operators.
-
ENX112 -
ESPEC North America, INC.
The ENX112 chambers provide a test chamber large enough for testing full-size PV modules in the least amount of floorspace. Can be use for panels 1.2m x 2m or larger.These models provide a variety of performance capabilities to meet maximum or minimum change rates in IEC or UL test standards. Incorporated are the features of our smaller Platinum and Global-N lines. The refrigeration systems of these models utilize modern, high performance scroll compressors that allow a small footprint while allowing unparalleled service access.
-
Greenlight Innovation
Greenlight's turn-key flow battery test systems include load/power supply modules, automated control of flow, pressure and temperature of electrolyte fluids, cell voltage monitoring, 3-level safety system and computer with Emerald dynamic automation software. All Greenlight flow battery test systems come with a our standard 1 year warranty. Our customer service team is available to travel to your facility for commissioning and training.Greenlight''s Automation Division also offers flow battery assembly equipment.
-
LD-LSPT-A10 -
Labodam
Automatic softening point testerLD-LSPT-A10is a bench top microprocessor controlled analytical unit that determines the softening point of two samples at once. Operated via touch panel it uses ball and ring apparatus for reliable detection. Designed as per Test methods of Bitumen and Bituminous Mixture for Highway Engineering and ASTM D36 Standard test method for Softening of Bitumen (Ring-and-Ball Apparatus) it is ideal for determining the softening points of petroleum asphalts, coal pitch, liquid petroleum asphalt, etc.
-
HV-Series -
L. A. B. Equipment, Inc.
L.A.B.’s HV Hydraulic Vibration Test Systems help you design high quality, cost-effective products and shipping containers by accurately measuring sensitivity to vibration. HV Systems are specifically designed to meet a wide range of ASTM, DOT, ISTA, ISO and federal standards for vibration testing. HV Systems are ideal for a wide spectrum of testing applications ranging from sine sweep tests to the most complex data real time simulation, or random reproduction applications.
